- name
Use when developing firmware for microcontrollers, implementing RTOS applications, or optimizing power consumption. Invoke for STM32, ESP32, FreeRTOS, bare-metal, power optimization, real-time systems
SKILL.md
The skill file stays in the publisher's repository.
Paste the copied command in a terminal. It installs this SKILL.md into that agent.
npx skills add Jeffallan/claude-skills --skill embedded-systems -a cursor -yPaste the copied command in a terminal. It installs this SKILL.md into that agent.
npx skills add Jeffallan/claude-skills --skill embedded-systems -a claude-code -yPaste the copied command in a terminal. It installs this SKILL.md into that agent.
npx skills add Jeffallan/claude-skills --skill embedded-systems -a codex -yPaste the copied command in a terminal. It installs this SKILL.md into that agent.
npx skills add Jeffallan/claude-skills --skill embedded-systems -a grok -ySend the copied message in a Grok Bot chat. The Bot fetches this SKILL.md from GitHub and adds it to the skills all your Bots share.
Install this skill: https://github.com/Jeffallan/claude-skills/tree/HEAD/skills/embedded-systemsFrom the publisher
Senior embedded systems engineer with deep expertise in microcontroller programming, RTOS implementation, and hardware-software integration for resource-constrained devices.
-Wall -Werror, verify no warnings; run static analysis (e.g. cppcheck); confirm correct register bit-field usage against datasheetuxTaskGetStackHighWaterMark(); measure ISR latency; confirm no missed deadlines under worst-case load; if issues found, return to step 4Load detailed guidance based on context:
volatile for hardware registers and ISR-shared variables/* Flag shared between ISR and task — must be volatile */
static volatile uint8_t g_uart_rx_flag = 0;
static volatile uint8_t g_uart_rx_byte = 0;
/* Keep ISR short: read hardware, set flag, exit */
void USART2_IRQHandler(void) {
if (USART2->SR & USART_SR_RXNE) {
g_uart_rx_byte = (uint8_t)(USART2->DR & 0xFF); /* clears RXNE */
g_uart_rx_flag = 1;
}
}
/* Main loop or RTOS task processes the flag */
void process_uart(void) {
if (g_uart_rx_flag) {
__disable_irq(); /* enter critical section */
uint8_t byte = g_uart_rx_byte;
g_uart_rx_flag = 0;
__enable_irq(); /* exit critical section */
handle_byte(byte);
}
}
#include "FreeRTOS.h"
#include "task.h"
#include "queue.h"
#define SENSOR_TASK_STACK 256 /* words */
#define SENSOR_TASK_PRIO 2
static QueueHandle_t xSensorQueue;
static void vSensorTask(void *pvParameters) {
TickType_t xLastWakeTime = xTaskGetTickCount();
const TickType_t xPeriod = pdMS_TO_TICKS(10); /* 10 ms period */
for (;;) {
/* Periodic, deadline-driven read */
uint16_t raw = adc_read_channel(ADC_CH0);
xQueueSend(xSensorQueue, &raw, 0); /* non-blocking send */
/* Check stack headroom in debug builds */
configASSERT(uxTaskGetStackHighWaterMark(NULL) > 32);
vTaskDelayUntil(&xLastWakeTime, xPeriod);
}
}
void app_init(void) {
xSensorQueue = xQueueCreate(8, sizeof(uint16_t));
configASSERT(xSensorQueue != NULL);
xTaskCreate(vSensorTask, "Sensor", SENSOR_TASK_STACK,
NULL, SENSOR_TASK_PRIO, NULL);
vTaskStartScheduler();
}
/* Demonstrates: clock enable, register-level GPIO, TIM2 interrupt */
#include "stm32f4xx.h"
void TIM2_IRQHandler(void) {
if (TIM2->SR & TIM_SR_UIF) {
TIM2->SR &= ~TIM_SR_UIF; /* clear update flag */
GPIOA->ODR ^= GPIO_ODR_OD5; /* toggle LED on PA5 */
}
}
void blink_init(void) {
/* GPIO */
RCC->AHB1ENR |= RCC_AHB1ENR_GPIOAEN;
GPIOA->MODER |= GPIO_MODER_MODER5_0; /* PA5 output */
/* TIM2 @ ~1 Hz (84 MHz APB1 × 2 = 84 MHz timer clock) */
RCC->APB1ENR |= RCC_APB1ENR_TIM2EN;
TIM2->PSC = 8399; /* /8400 → 10 kHz */
TIM2->ARR = 9999; /* /10000 → 1 Hz */
TIM2->DIER |= TIM_DIER_UIE;
TIM2->CR1 |= TIM_CR1_CEN;
NVIC_SetPriority(TIM2_IRQn, 6);
NVIC_EnableIRQ(TIM2_IRQn);
}
When implementing embedded features, provide:
Maintained by @jeffallan, Principal Consultant at Synergetic Solutions
© 2026 Skills Rack.
---name: embedded-systemsdescription: Use when developing firmware for microcontrollers, implementing RTOS applications, or optimizing power…---# skills/embedded-systems/SKILL.mdOverview
Use when developing firmware for microcontrollers, implementing RTOS applications, or optimizing power consumption. Invoke for STM32, ESP32, FreeRTOS, bare-metal, power optimization, real-time systems, configure peripherals, write interrupt handlers, implement DMA transfers, debug timing issues.
FAQ
Download skills/embedded-systems/SKILL.md from the publisher, or copy the path and open the repository. PlugMCP lists the skill and does not host the file.
The publisher keeps it at https://github.com/Jeffallan/claude-skills.
Claude, Cursor, Codex, and Grok Build can read a SKILL.md you add from the publisher's repository. Grok Bot installs it when you send the skill's GitHub folder link in a chat.